Chat Now
Position:Home - News - Industry NewsIndustry News
CABLE TRAY BRIEFING
Time:2013-09-27 8:11:01 Views:1
Cable Tray is available in variation based on the environmental and weather conditions for which it is used. Either 300 or 600 Volt with THHN, XLPE and EPR insulations are available, each with unique advantages and usages. From an expense standpoint, 600 volt Cable Tray carries a higher cost than the 300 volt due to the higher energy level. With the different types of insulations, EPR insulation carries a higher expensive due to its nature and what more it offers over THHN and XLPE cables.

A job site, field adaptable support system primarily for low voltage, telecommunication and fiber optic cables. These systems are typically steel wire mesh, zinc plated.
standard widths of 2, 4, 6, 8, 12, 16, 18, 20, and 24 inches
standard depths of 1, 2, and 4 inches
standard length of about 10 feet (118")
Wire Mesh tray is generally used for telecommunication and fiber optic applications and are installed on short support spans, 4 to 8 feet. 
 
2.Single Rail Cable Tray provides:
These aluminum systems are the fastest systems to install and provide the maximum freedom fort cable to enter and exit the system.
Single hung or wall mounted systems in single or multiple tiers.
Standard widths are 6, 9, 12, 18, and 24 inches.
Standard depths are 3, 4, and 6 inches.
Standard lengths are 10 and 12 feet.
Single Rail Cable Tray is generally used for low voltage and power cables installations where maximum cable freedom, side fill, and speed to install are factors.

3.Channel Cable Tray provides:
an economical support for cable drops and branch cable runs from the backbone Cable Tray system.
standard widths of 3, 4, and 6 inches in metal systems and up to 8 inches in nonmetallic systems.
standard depths of 1¼-1¾ inches in metal systems and 1, 1 1/8, 1 5/" and 2 3/16 inches in nonmetallic systems
standard length of 10, 12, 20 and 24 feet
Channel cable tray is used for installations with limited numbers of Cable Tray when conduit is undesirable. Support frequency with short to medium support spans of 5 to 10 feet.

4.Trough Cable Tray provides:
Moderate ventilation with added cable support frequency and with the bottom configuration providing cable support every 4 inches. Available in metal and nonmetallic materials.
standard widths of 6, 12, 18, 24, 30, 36 inches
standard depths of 3, 4, 5, and 6 inches
standard lengths of 10, 12, 20 and 24 feet
fixed rung spacing of 4 inch on center
Trough cable tray is generally used for moderate heat generating applications with short to intermediate support spans of 5 feet to 12 feet. 

5.Solid Bottom Cable Tray provides:
Nonventilated continuous support for delicate cables with added cable protection available in metallic and fiberglass.
Solid bottom metallic with solid metal covers for nonplenum rated cable in environmental air areas
standard widths of 6, 12, 18, 24, 30, and 36 inches
standard depths of 3, 4, 5, and 6 inches
standard lengths of 10, 12, 20 and 24 feet
Solid Bottom cable tray is generally used for minimal heat generating electrical or telecommunication applications with short to intermediate support spans of 5 feet to 12 feet. 

6.Ladder Cable Tray provides:
Solid side rail protection and system strength with smooth radius fittings and a wide selection of materials and finishes.
maximum strength for long span applications
standard widths of 6,12,18, 24, 30, and 36 inches
standard depths of 3, 4, 5, and 6 inches
standard lengths of 10, 12, 20 and 24 feet
rung spacing of 6, 9, 12, and 18 inches
Ladder cable tray is generally used in applications with intermediate to long support spans, 12 feet to 30 feet. 
Wire Mesh Cable Tray    CABLE TRAY    CABLE LADDER    CABLE SUPPORT    CABLE DUCT    CABLE TRUNKING   
Right Reserved © 2013 Shanghai Aifan Metal Co.,Ltd HU ICP11010236-1